ATxmega32a4 XMEGA development board USB-UART AVRISPmkII

Sold See similar items $37.88 Buy It Now, $9.46 Shipping, 30-Day Returns, eBay Money Back Guarantee
Seller: denebx ✉️ (1,483) 0%, Location: Heppner, Oregon, US, Ships to: WORLDWIDE, Item: 140565584469 ATxmega32a4 XMEGA development board USB-UART AVRISPmkII. Introduction        The MT-X4-UX is a flexible USB development board for the Atmel ATxmega32a4 microcontroller. The XMEGA can be fully programmed over USB using the onboard AVRISPmkII-compatible PDI programmer (no need to purchase an external programmer). The XMEGA can communicate with a computer using the onboard USB to serial bridge. Speeds up to 2Mbps are supported in synchronous mode (1Mbps in asynchronous mode). The Atmel AT90USB162 USB AVR, which provides these features, will automatically sleep when USB is disconnected. The board can be powered via USB or an external header. Voltage is regulated by a 3.3V, 500mA LDO regulator. There are several clock options available onboard, including a 32.768KHz crystal, an external 8MHz clock, an external HC49 crystal landing, and several internal clock options. A demo program is preinstalled on the XMEGA demonstrating the USB to serial bridge, RTC, and sleep mode. The MT-X4-UX comes on a DIL-40 size with standard 0.1” header pin spacing. Note that the photos do not show the included 32.768KHz crystal. The actual button has a lower profile than shown. MT-X4-UX Features *   Atmel XMEGA 32A4, 32KB flash, 4KB RAM, 1KB EEPROM *   Onboard USB PDI programmer (no external programmer needed)     *   AVRISPmkII compatible     *   Program flash, EEPROM, fuses, lock bits, and more     *   Works with AVR Studio 4 and 5, AVRDUDE, Codevision, and BASCOM 2.0.6 *   USB - Serial Bridge     *   Up to 2MHz baud rate (1MHz async)     *   Synchronous or asynchronous operation     *   Optional USB ready signal *   3.3V, 500mA LDO regulator *   Powered via USB or external header *   32.768KHz crystal connected to TOSC (RTC) pins *   8MHz external clock available from USB AVR *   HC49 crystal landing connected to XTAL pins *   PDI Header* *   4 boot modes selectable via 2 jumpers     *   USB-UART bridge (default)     *   AVRISPmkII compatible PDI programmer     *   Configuration (uses terminal emulator)     *   DFU bootloader (to update firmware on USB AVR via USB) *   Reset button can be used to toggle between the PDI programmer and the serial bridge *   Preloaded demo program demonstrates the USB to serial bridge, RTC, and sleep mode *   PCB measures 5.2cm x 2.05cm (DIL-40 with standard 0.1” pin spacing) *  Compatible with Windows XP/Vista/7 and Linux *   Uses LUFA USB library and AVRISPmkII by Dean Camera ([link removed by eBay] )

Documentation

   User Manual (In progress)  Headers Standard headers and machined pin headers are available. Machined pin headers have round pins and can be used in chip sockets. They are also easier to breadboard.

Standard Headers

Machined Pin Headers

Schematic

 Export Information Shipping for the A variant (ATxmega32a4) is available to the following countries only (sorry, no exceptions): USA, Austria, Australia, Bulgaria, Belgium, Canada, Cyprus, Czech Republic, Estonia, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Japan, Latvia, Lithuania, Luxembourg, Malta, Netherlands, New Zealand, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey, United Kingdom Due to export restrictions, further information sent via email may be required. The D variant (ATxmega32d4) is available worldwide (see other listing).

Hex Files for MT-X4-UX

  MT_X4_UX.hex   Revision 110617   MT_X4_UX.eep   Revision 110617   XMEGA_Demo.hex   Revision 110617 The MT_X4_UX.hex file contains the AVRISPmkII compatible PDI programmer, serial bridge, and configuration that comes pre-installed on the USB AVR The MT_X4_UX.eep file contains the default configuration that comes pre-installed on the USB AVR The XMEGA_Demo.hex file demonstrates the onboard peripheral devices and sleep mode. It is pre-installed on the XMEGA and utilizes the serial bridge to communicate with a terminal emulator.

Copyright (c) 2009-2011, Justin Mattair Copyright (c) 2009-2010, Dean Camera Copyright (c) 2003-2010, Atmel Corporation Source code   MT-X4-UX_110617.zip   Revision 110617 This file contains all of the source code for the XMEGA demo. Copyright (c) 2009-2011, Justin Mattair Copyright (c) 2003-2010, Atmel Corporation

Drivers    MT_X4_UX.inf An .inf file is required for the serial bridge, configuration, and XMEGA demo program if running Windows, when it will operate as a CDC-ACM device (virtual COM port). This file supports Windows 2000, XP, Vista (32 and 64 bit) and Windows 7 (32 and 64 bit). Linux does not require a download (drivers should already be installed). The AVRISPmkII compatible PDI programmer requires a driver provided by Atmel as a part of AVR Studio (see manual). The DFU Bootloader also requires a driver. This driver is included with FLIP (inside the USB folder of FLIP's directory). If using Windows Vista 64-bit or Windows 7 64-bit, you may need to download signed drivers from [link removed by eBay] . The latest version of FLIP should not require this. License / Disclaimer Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notices appear in all copies and that both that the copyright notices and this permission notice and warranty disclaimer appear in supporting documentation, and that the name of the authors not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission. The author disclaim all warranties with regard to this software, including all implied warranties of merchantability and fitness. In no event shall the author be liable for any special, indirect or consequential damages or any damages whatsoever resulting from loss of use, data or profits, whether in an action of contract, negligence or other tortious action, arising out of or in connection with the use or performance of this software.

Ordering & Payment All payments are handled through PayPal's secure server. It is not necessary to have a PayPal account to make a purchase. Payment methods include all major credit cards, debit cards, and PayPal funds. If you need a tax ID, please call or email.

Shipping & Delivery All shipments are handled by the United States Postal Service. We ship both domestically and to most international locations. Most orders ship the same or next day. You will receive a tracking number once your order has shipped. All shipments are insured. We do not accept C.O.D. orders.        Any shipping taxes, duty, or any other fees are the responsibility of the buyer. We will not mark shipments as gifts or reduce the invoice amount. Residents of the UK are urged to select Express mail due to customs delays.
  • Condition: New
  • Standard headers: not included
  • Machined pin headers: not included
  • Platform: Windows, Linux

PicClick Insights - ATxmega32a4 XMEGA development board USB-UART AVRISPmkII PicClick Exclusive

  •  Popularity - 1 watcher, 0.0 new watchers per day, 87 days for sale on eBay. Normal amount watching. 1 sold, 10 available.
  •  Best Price -
  •  Seller - 1,483+ items sold. 0% negative feedback. Good seller with good positive feedback and good amount of ratings.

People Also Loved PicClick Exclusive